Best Aqara Water Leak Sensor T1 — Expert Picks & Deals (November 2026)
Aqara Water Leak Sensor T1
The Aqara Water Leak Sensor T1 is the pick for people who already run a smart home. It is a small white puck, 50 x 50 mm, with two gold-plated probes on the bottom. When as little as 0.5 mm of water bridges those probes, it sends an instant alert over Zigbee 3.0 to your Aqara hub, which pushes a notification to your phone and can trigger automations — flashing your lights, sounding a hub alarm, or closing a smart valve. It is IP67-rated, runs on a coin cell rated for up to two years, and costs about $18 to $20 per sensor as reviewed.
A slow leak under a sink, a washing machine hose that lets go at 2 a.m., a water heater that quietly fails while you are on holiday — by the time you see the water, the floor, the ceiling below and your insurance excess are already involved. A sensor like the T1 is the cheapest insurance you can buy: a small puck on the floor that alerts you the moment water touches it.
The T1's strength is also its catch: it needs an Aqara hub. If you already own one, adding sensors is cheap and the Zigbee mesh is fast and reliable, without touching your Wi-Fi at all. If you do not own a hub, the hub adds roughly $30 to $50 to the first sensor's real cost, and the sensor has no siren of its own — the alarm comes from the hub or your phone. It also works with Apple HomeKit (via the hub), Home Assistant, SmartThings and Hubitat, which makes it the most flexible sensor in its group for automation fans.
How to choose
- Smart home platform: the T1 is best for Apple Home and Home Assistant households with an Aqara hub. It works with HomeKit, Home Assistant, SmartThings and Hubitat.
- Hub: an Aqara hub is required — an extra cost of roughly $30 to $50 if you do not own one.
- Alarm: there is no built-in siren; the alarm comes from the hub or your phone. The Govee and YoLink sensors have loud built-in alarms instead.
- Placement: put sensors where water actually pools — under the kitchen sink, behind the washing machine and dishwasher, next to the water heater, under bathroom sinks and toilets, near the basement sump pump.
- Automations: the T1 can trigger automations such as flashing lights, sounding a hub alarm or closing a smart valve — though it cannot shut off water on its own.
- Maintenance: test sensors every few months with a wet finger, and replace batteries on schedule — a dead sensor is worse than no sensor.
Top picks
The Aqara Water Leak Sensor T1 is the source guide's best for Apple Home and smart home automations — tiny, IP67-rated, Zigbee 3.0, and around $18 to $20 per sensor. Its 0.5 mm trigger sensitivity and deep automation support set it apart.
For most homes, the guide's best overall value is the Govee WiFi Water Sensor — a loud 100 dB alarm, Wi-Fi alerts with no subscription, and cheap multi-packs for whole-home coverage. For large homes and outbuildings, the YoLink Water Leak Sensor 4 is the pick, with LoRa range up to 2,034 ft and up to 5 years of battery life. And for whole-home protection, the Moen Flo Smart Water Monitor and Shutoff is the only pick that actually stops the water, not just tells you about it.
Frequently asked questions
Does the Aqara Water Leak Sensor T1 need a hub?
Yes. It needs an Aqara hub, and it sends alerts over Zigbee 3.0 to the hub, which pushes a notification to your phone. If you do not own a hub, the hub adds roughly $30 to $50 to the first sensor's real cost.
Does the Aqara Water Leak Sensor T1 have a siren?
No. The sensor has no built-in siren of its own — the alarm comes from the hub or your phone. It can trigger automations, such as flashing your lights, sounding a hub alarm or closing a smart valve.
Do smart water leak detectors need a subscription?
No, for all the picks in the comparison. Aqara charges nothing monthly, and neither do Govee or YoLink. Moen Flo's app is free, with an optional FloProtect plan at $5 a month for an extended warranty and deductible cover.